Guide (Airlock) - Revision history

107.130.85.220: /* Variants */

2026-01-15T03:41:04Z

‎Variants

2026-01-15T03:29:09Z

‎Variants

2026-01-15T03:26:25Z

It is possible to "reset" the airlock circuit board using a screwdriver.

2025-03-30T14:37:32Z

‎Variants

2023-02-06T03:17:37Z

‎Variants

2023-02-06T03:17:09Z

‎Description

2023-02-06T03:16:32Z

‎Description

2019-06-16T04:17:45Z

‎Variants

2019-06-16T04:16:19Z

2019-03-18T09:30:02Z

add See Also links

@@ Line 20: / Line 20: @@
 Whichever route you take, it is good practice to put an Area Power Controller inside the airlock to allow a user to power it using batteries should a stations power grid fail.
-If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard using the Data Disk. This will ensure that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.
+If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard. Use the screwdriver on the console's side screw to change it into configuration mode, then deselect all devices. This will ensure that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.
-You can then use a screwdriver to reset the Circuitboard which will delete all device references stored on the board. Drop the board on the ground and hover over it with the screwdriver, then hold left mouse button to reset it.
+You can then use a screwdriver to reset the Circuitboard which will delete all device references stored on the board. Remove the board from the console, drop it on the ground and hover over it with the screwdriver, then hold left mouse button to reset it.
 ==See Also==

@@ Line 20: / Line 20: @@
 Whichever route you take, it is good practice to put an Area Power Controller inside the airlock to allow a user to power it using batteries should a stations power grid fail.
-If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard using the Data Disk. This will ensure that the said Circuitboard will remain fully operational, rather than "ruined" by the deprecated links to objects that cannot be undone, and that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.
+If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard using the Data Disk. This will ensure that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.
-You can use a screwdriver to reset the Circuitboard. Drop the board on the ground and hover over it with the screwdriver, then hold left mouse button to reset.
+You can then use a screwdriver to reset the Circuitboard which will delete all device references stored on the board. Drop the board on the ground and hover over it with the screwdriver, then hold left mouse button to reset it.
 ==See Also==

← Older revision		Revision as of 03:26, 15 January 2026
Line 21:		Line 21:

	If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard using the Data Disk. This will ensure that the said Circuitboard will remain fully operational, rather than "ruined" by the deprecated links to objects that cannot be undone, and that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.		If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard using the Data Disk. This will ensure that the said Circuitboard will remain fully operational, rather than "ruined" by the deprecated links to objects that cannot be undone, and that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.
		+
		+	You can use a screwdriver to reset the Circuitboard. Drop the board on the ground and hover over it with the screwdriver, then hold left mouse button to reset.

	==See Also==		==See Also==

← Older revision		Revision as of 14:37, 30 March 2025
Line 19:		Line 19:

	Whichever route you take, it is good practice to put an Area Power Controller inside the airlock to allow a user to power it using batteries should a stations power grid fail.		Whichever route you take, it is good practice to put an Area Power Controller inside the airlock to allow a user to power it using batteries should a stations power grid fail.
		+
		+	If you want to relocate, modify or remove an existing airlock setup, make sure to first disable all the device references set up in the console's Circuitboard using the Data Disk. This will ensure that the said Circuitboard will remain fully operational, rather than "ruined" by the deprecated links to objects that cannot be undone, and that doors and vents will be unlocked properly for manual operation before being dismantled or uninstalled.

	==See Also==		==See Also==

@@ Line 17: / Line 17: @@
 | [[Guide (Airlock) Docking Ports|Docking Ports]] || 1 x [[Kit (Mothership)]] || Traverse between a stationary base and a Mothership, or between Motherships
 |}
 ==See Also==

@@ Line 3: / Line 3: @@
 <translate>
 ==Description==
-An airlock is a [[Room|chamber]] that can evacuate, modify, or fill its internal volume with differing [[Atmosphere|atmospheres]] and has two or more airtight portals which all do not open simultaneously. Thus, an airlock allows passage between two or more environments without the exchange of [[Gas|gases]] or [[Pressure|pressures]] between the connected atmospheres. It is good practice to put an [[Area Power Controller|Area Power Controller]] inside the airlock to allow a user to power it using batteries should a stations power grid fail.
+An airlock is a [[Room|chamber]] that can evacuate, modify, or fill its internal volume with differing [[Atmosphere|atmospheres]] and has two or more airtight portals which all do not open simultaneously. Thus, an airlock allows passage between two or more environments without the exchange of [[Gas|gases]] or [[Pressure|pressures]] between the connected atmospheres.
 ==Variants==

@@ Line 9: / Line 9: @@
 {| class="wikitable"
 |-
-! Guide Varient !! Defining Component || Characteristics
+! Guide Variants !! Defining Component || Characteristics
 |-
 | [[Guide (Airlock) Atmosphere to Atmosphere|Atmosphere to Atmosphere]] || 1 x [[Circuitboard (Advanced Airlock)]] || Traverse between two environment with differing atmospheres

@@ Line 19: / Line 19: @@
 ==See Also==
 * [[Circuitboard (Advanced Airlock)]]
 * [[Circuitboard (Airlock)]]
 * [[Kit (Airlock)]]
 </translate>